Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 55

Страница: 55 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

10000001052

1.4.5.1.7

Error Considerations

- No Position

- No or invalid Status

- No Heading (see section 7.3.2.1)

- Missing Waypoint

- Track control impossible.

ATTENTION:

If an error occurs during Track Control, the operating mode changes from

Track Control to Heading Control.

As opposed to manual change- over from Track Control to Heading Control, the

setting of the maneuver parameters might maintain as under Track Control.

I. e.:

On straight leg:

- All values will be adopted from Heading Control mode. On curved path:

- The radius planned for the next track change maneuver is maintained.

- The rudder limit remains at Max.

Alert Check Settings” is displayed (see section 1.4.5.1.7.2).

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды