Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 186

Страница: 186 / 191

NautoPilot Operator Unit

8 Annex

10000001052

Edition:001

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

TCS STOPPED
MAG HDG SELECT-

ED: SELECT GYRO

HEADING

Warning
B

Alarm
to BN-

WAS
(30 s)*

Track control inter-

rupted, magnetic

heading source se-

lected.

Select gyro heading

source.

TRCK-

CRS-HDG.DIFF
TAKE HELM TO

KEEP COURSE

STEADY

Warning
A

Warning

Difference between

actual heading and

leg course exceeds

operator adjusted off

course limit.

Check surroundings,

high drift or other dis-

turbances present.

WP APPROACH
APPROACH NEXT

WAYPOINT

Warning
A

Warning

Track control in

accordance with

IEC62065:2002 con-

figured. Next way-

point in 3 min.

AP NOT ACTIVE
AUTOPILOT NOT

ACTIVE: ACTIVATE

HDG CONTROL

Caution
B

Heading control has

to be active to acti-

vate Track control

Activate Heading con-

trol

APPROACH WP
APPROACHING

NEW WAYPOINT

Caution
B

none

CC UNAVAIL.
NO POSITION:

CHECK POS

SENSORS

Caution
B

none

No position infor-

mation available so

Course control is not

usable.

Check position sen-

sors.

GYRO NOT SEL
NO TCS OR

CC WITH MAG:

SELECT GYRO

HEADING

Caution
B

none

TCS may not be used

in when a magentic

heading source is se-

lected

Select Gyro compass

as heading source

HCS UNAVAIL.
NO HEADING:

CHECK HDG

SENSORS

Caution
B

none

Activation of Track or

Course control while

no speed is avaiable

- activation not possi-

ble.

MISSING WP
MISSING WAY-

POINTS

Caution
B

none

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды