Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 181

Страница: 181 / 191

NautoPilot Operator Unit

8 Annex

Edition:001

10000001052

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

HDG MON DIS.
HEADING MONI-

TOR DISABLED

Caution
B

none

HDG UNCORR.
CHECK HEADING

CORRECTION

Caution
B

none

Gyro reports uncor-

rected heading infor-

mation.

Check Gyro

INP NOT ACCEPT-

ED
INPUT NOT AC-

CEPTED: REPEAT

INPUT

Caution
B

none

Inplausable Input,

e.g. Set Heading.

Repeat input.

LOW SPEED
CTRL ACCURACY

MAY BE LIMITED

Caution
B

Autopilot in standby

and current speed is

below adjusted low

speed limit.

none necessary. In-

crease speed prior

to activating Heading

control.

MAG FAILED
BACK UP HDG

SENSOR FAILED:

CHECK SENSOR

Caution
B

none

Magnetic compass

connected to AP

failed.

Check magnetic com-

pass.

NO BACKUP GYRO
NO BACKUP GYRO

AVAILABLE

Caution
B

none

Backup gyro reports

failure.

Check backup gyro

NO RUD. CTRL
NO RUDDER CTRL

ON CAN: USE MAN-

UAL STEERING

Caution
B

Take over of rudder

control not success-

ful.

Check steering sys-

tem.

NO SET HDG
SET HDG REJECT-

ED: ENTER NEW

SET HEADING

Caution
B

none

Error during set head-

ing adjustment

Repeat set heading

adjustment

NOT SPD ADAP-

TIVE
NO SPEED ADAP-

TIVITY: CHECK

SPEED SENSOR

Caution
B

none

No speed information

available.

Check speed sen-

sors, adjust manual

speed.

OU CHANGE
ACTIVE OPERATOR

UNIT CHANGED

Caution
B

none

Another OU was acti-

vated and is now the

active OU.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды