Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 17

Страница: 17 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

10000001052

1 Description

The NautoPilot® 5000 Series is part of the Steering System Family AS (Advanced

Steering) and is used to control navigation at sea for all sizes of seagoing vessels.

The NautoPilot® 5000 Series was designed for use in high speed craft, but is

equally suited for all types of mono- and multihull vessels with any kind of

rudder control.

The NautoPilot® 5000 Series complies with IMO resolutions.
By setting a number of easily accessible parameters, the Autopilot’s steering

characteristics can be adjusted (depending on the type of NautoPilot® 5000 Series)
to the vessel’s dynamic behavior and the prevailing conditions (sea state, load).

There are 4 different types of NautoPilot® (which vary in different operation

modes) and 2 different applications:

Type: NP 5100

Type: NP 5300

Type: NP 5400

Type: NP 5500

Application:

Stand alone

Application:

Integrated

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды