Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 180

Страница: 180 / 191

NautoPilot Operator Unit

8 Annex

10000001052

Edition:001

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

CHECK LIMITS
CHECK RUD-

DER/ROT/RAD

LIMITS

Warning
B

Warning

Track control was in-

terrupted.

The operator shall

check the limits for

RAD/ROT and Rud-

der limits. Those

might have changed

by the TCS.

HCS UNAVAIL.
NO HEADING:

CHECK HEADING

Caution
B

Autopilot in standby,

but no heading da-

ta available. Heading

control cannot be ac-

tivated.

Check Heading sen-

sors.

HCS UNAVAIL.
POWER FAILURE:

CHECK POWER

SUPPLY

Caution
B

none

Power supply of the

opertor unit is outside

of tolerable limits, the

device is in standby

mode

Check power supply.

HCS UNAVAIL.
NO STEERING

MODE: USE MANU-

AL STEERING

Caution
B

Status of Steering se-

lector switch is not

available. AP is in

standby and cannot

be activated.

Check steering sys-

tem.

HCS UNAVAIL.
APIF: AUTOPILOT

ACTIVATION

FAILED

Caution
B

AP was not activated.

HCS UNAVAIL.
CANNOT ACTIVATE

HCS: USE MANUAL

STEERING

Caution
B

Unexpected be-

haviour in case of

giveover of rudder

control by steering

system.
Heading control not

activated.

HDG CHANGE
SENSOR USED

FOR CONTROL

FUNCTION

CHANGED

Caution
B

none

Automatic change of

selected heading sen-

sor.

HDG DOUBTFUL
FUNCTION NOT

ACTIVATABLE

Caution
B

none

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды