Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 189

Страница: 189 / 191

NautoPilot Operator Unit

8 Annex

Edition:001

10000001052

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

CC STOPPED
POSITION JUMP:

CHECK POSITION

Warning
B

Alarm
to BN-

WAS

Position jump detect-

ed, Course control is

interrupted. Fallback

is Heading control.

HDG MONITOR
HEADING IN-

TEGRITY LOW:

CHECK HEADING

SENSORS

Warning
B

Doubtful heading in-

formation or heading

monitor not available

Check heading infor-

mation, use manual

steering

NO POS MON
DEAD RECKONING

NOT AVAILABLE

Warning
A

Alarm

Position monitoring

not possible, lack of

data

Check connected

sensors

OFF COURSE
DISTANCE TO

COURSE LINE EX-

CEEDS LIMIT

Warning
A

Distance to course

line exceeds operator

adjusted limit.

Check surroundings,

use manual steering

POS DOUBTFUL
POSITION DIF-

FERENCE:

CHECK POSITION

SENSORS

Warning
A

Warning

Position monitor de-

tected a difference

between position in-

formation.

Check position sen-

sors, use heading

control.

BACK. POS CHNG
BACKUP POSTION

SENSOR CHANGED

Caution
B

none

Backup Position sen-

sor for position moni-

toring changed.

None necessary.

CC NOT ACT.
ACTIVATE HDG

CONTROL

Caution
B

none

Heading control has

to be active to acti-

vate Course control

Activate Heading con-

trol

CC NOT AVAIL.
TURN RATE TOO

FAST (LIMIT:30°/

MIN)

Caution
B

none

Ship is turning to fast

- Course control can

not be activated

Wait until the turn is

completed.

CC UNAVAIL.
CC NOT INCLUDED,

USE HDG CTRL

Caution
B

none

Course control is not

available for this de-

vice

Upgrade License

CC UNAVAIL.
MAG HEADING

SELECTED

Caution
B

none

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды