Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 129

Страница: 129 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

113

10000001052

4.4 Course Control

4.4.1

Preconditions for switching to Course Control mode

Table 26

Checks to be made before switching to Course Control mode

Check

Comment

Heading source

The desired heading source is shown above the actual
heading value.
The heading source can be adjusted via the Page
function: Softkeys Page

→

Value

→

Heading

(see also section 2.3.6.1 and Figure 44).
Gyro or GPS must be selected. It is not possible to use
magnetic heading.

Heading value

The heading value must be valid.

- Check actual heading, as this will be the

set Course over Ground after switching to
Course Control.

A direct switchover from ”Manual” mode to

”Course Control” mode is not possible.

- A direct switchover f

rom ”Track Control” mode to

”Course Control” mode is not possible.

A direct switchover to ”Course Control” is only possible

from ”Heading Control” mode.

A direct switchover from Override” to Course Control” is
not possible.

”Course Control” mode is not possible without a
valid position.

Activation of ”Course Control” mode is not possible with
a turn rate of more than 29



/minute during a heading

change.

A mode change from ”Heading Control” to ”Course

Control” should not be performed during a heading

change in ”Heading Control”, because of the limited turn

rate and the fact, that the actual heading is set as the ”set

course” at the same time as ”Course Control” is activated.
It is therefore advisable to finish a heading change in

”Heading Control” mode” before switching over to ”Course

Control” mode.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды