Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 20

Страница: 20 / 191

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

Edition: 003

Additional Autopilot Control Unit (AACU)

The Additional Autopilot Control unit can be purchased in addition (optional) to

the NautoPilot®.

It is a slave console of the NautoPilot® and consists of a joystick and a 12 monitor.

In addition, the AAC enables the graphical representation of a curved heading line in

the Raytheon SYNAPSIS NX ECDIS and RADAR.

Table 1

Overview NautoPilot® types (variants)

Heading

Control

Course

Control

Weather

Adaptivity

Track

Control

Category B*

Track

Control

Category C*

Cross

Acceleration

Monitor

High

Precision

Controller

NP 5100

✓

NP 5300

✓

NP 5400

✓

NP 5500

✓

Please note:
This manual contains information for all types and modes.
Some sections are marked for their validity.

Note:

* For Track Control Category B and C:

In February 2014 the test standard for track control systems IEC 62065 has been

re- vised to edition 2. Please not that only NautoPilot® 5400 and 5500 have been

adapted to the latest test standard (introduced with software version E03).

NautoPilot® 5100 and 5300 are compliant to IEC 62065 edition 1 with software

versions E01 and E02.

Figure 2: Additional Autopilot Control Unit (AACU)

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды