Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 187

Страница: 187 / 191

NautoPilot Operator Unit

8 Annex

Edition:001

10000001052

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

NEW TRACK
NEW TRACK 000°

Caution
B

none

Track change maneu-

ver is complete.

none necessary.

NO RADIUS
NO APPROACH

RAD. DEFINED

Caution
B

none

NO TRACK CRS
CHECK CONNEC-

TION TO ECDIS

Caution
B

none

NO TRC DATA
CHECK CONNEC-

TION TO ECDIS

Caution
B

none

NOT SPD ADAP-

TIVE
NO SPEED: CHECK

SPEED SENSOR

Caution
B

none

Activation of Track or

Course control while

no speed is avaiable

- activation not possi-

ble.

POWER FAIL.
CHECK POWER

SUPPLY

Caution
B

none

TCS NOT ACTIVAT.
APPROACH ANGLE

GREATER THAN

60°

Caution
B

none

Track control can on-

ly be activated if ac-

tual heading is within

a cone of +- 60° from

the leg course.

Steer the ship, so it is

within the cone, ad-

just track

TCS NOT ACTIVAT.
ACTIVATE TRACK

CONTROL ON

ECDIS

Caution
B

none

Attempted to activate

Track at the Operator

unit.

Track control mode

can only be activated

at ECDIS

TCS UNAVAIL.
NO POSITION:

CHECK POS

SENSORS

Caution
B

none

No position infor-

mation available so

Track control is not

usable.

Check position sen-

sors.

TCS UNAVAIL.
NO POSITION:

CHECK POSITION

Caution
B

none

No position data

available, AP is not

in track control. Track

control cannot be ac-

tivated.

Check position sen-

sors.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды