Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 191

background image

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

XIV

Edition: 003

There are 2, versions of the NautoPilot® Operator Unit available.
They differ in the housing dimensions.

For version

•

NG001 see appended dimensional drawing 102-890.
HP005

•

NG002, NG003 see appended dimensional drawing 102-
890. HP015

NautoSteer AS consists of 2 independent steering control
systems that are technically separated from each other. These
steering control systems can be selected by using the steering
mode selector switch.

In NFU direct mode the valves / steering gear are operated
directly without the use of electronics.

In main mode a closed loop control system is used.

Recommendation:
In case of any failure in either 1 of the 2 independent steering
control systems please switch to the other mode by using the
steering mode selector switch to retrieve the steering
capabilities of the control system (see also section 1.3.11).

Please note that depending on the system design the steering
control system may not contain a steering mode selector
switch. In this case it is strongly recommended to be familiar
with the steering control system in order to select the right
steering control in emergency situations.

«
...
14
15
16
17
18
...
»

Содержание NautoPilot 5000 Series
































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NautoPilot 5000 Series

Бренд: Icom Страницы: 27

Бренд: Icom Страницы: 72

Бренд: M-system Страницы: 5

Бренд: MA Страницы: 2

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

Бренд: VDO Страницы: 15

Бренд: VDO Страницы: 20

Бренд: Össur Страницы: 16

Exoform Dorsal Night Splint

Бренд: Össur Страницы: 34

Бренд: Warner Electric Страницы: 14

Бренд: Biosonic Страницы: 2

Бренд: Petzl Страницы: 7

RGB Studio Beam Driver

Бренд: SHOWTEC Страницы: 16

Бренд: Hanskamp Страницы: 22

ALFW-6LU-5KBZ Series

Бренд: Hubbell Страницы: 2

Бренд: SIMES Страницы: 8

Giotto spot 400

Бренд: SGM Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды