Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 170 | Manualshive

Страница: 170 / 191

background image

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

154

Edition: 003

(see also Table of alert icons, section 7.1)
In addition to the acoustic signal, the (red) ACK LED flashes.

The acoustic signal has both a low volume signal and a loud signal (from 2

different signal horns).

Each alert is combined with a priority. This priority is generated by the NautoPilot®
Operator Unit and depends on the operating mode, operating status and severity.

Each alarm or warning must be acknowledged with the ACK button.

If several alerts occur, the one with the highest priority is displayed at the bar (short

text). Priority of alerts is set internally. After pressing the ACK button all alerts are

displayed (one after another for approx. 3 seconds). After pressing the ACK button

again the alert with the highest priority is shown.

If an alert consists of more than 1 text line, those will be displayed one after

another. In this case the alerts will also be numbered [1], [2],

…

If the cause which leads to an alarm or a warning is eliminated without

acknowledgement (pressing the ACK button), the acoustic signal stops and the

alarm will be given lowest priority.

The table in the annex shows all possible messages, their possible cause and

recommendations for corrective action.

Please note:
It is also possible to acknowledge alerts at an inactive
NautoPilot® Operator Unit.

Please note:
Cautions and information messages do not necessarily
have to be acknowledged.
They are no longer displayed if their cause is no longer
present.

«
...
168
169
170
171
172
...
»

Содержание NautoPilot 5000 Series
































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NautoPilot 5000 Series

Бренд: ABB Страницы: 14

Бренд: GE Страницы: 2

Druck DPI 620 Genii

Бренд: GE Страницы: 154

Arize Element Top Light

Бренд: GE Страницы: 2

Бренд: Datex-Ohmeda Страницы: 104

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 166

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 340

Бренд: vanEE Страницы: 52

Бренд: Caddon Hives Страницы: 3

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: Parker Страницы: 39

Бренд: MacDon Страницы: 2

Бренд: Major tech Страницы: 12

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

Бренд: Quantum Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды