Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 157

Страница: 157 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

141

10000001052

5.6 Alerts of the Additional Autopilot Control Unit

Alerts are given acoustically and are shown on the NautoPilot® Operator Unit,

ECDIS and Radar.

For more Information see chapter 7 Alert/status message handling for NautoPilot®

and the chapters Alert Area and Alert Management in the Software Manuals of

ECDIS and Radar.

If the data transfer fails in Heading Control Mode, this alarm appears in the field

AUTOPILOT VALUES. The NautoPilot® main unit takes control again.

In this case the Additional Autopilot Control Unit goes into standby mode. If the

failure has been corrected, the Heading Control Mode must be selected again, see

5.4.1 Heading Control.

5.7 Show / Hide the Curved Heading Line

Select the softkey CHL ACTIVE in the Section CONTROL. The softkey is

highlighted and the Curved Heading Line is displayed on the RADAR and

ECDIS.

Select the softkey again to hide the Curved Heading Line. The softkey is not
highlighted.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды