Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 177

Страница: 177 / 191

NautoPilot Operator Unit

8 Annex

Edition:001

10000001052

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

GYRO FAILED
APIF GYRO HEAD-

ING FAILED:

CHECK HDG

SENSOR

Caution
B

none

Gyro connected at

APIF failed.

Check Gyro connect-

ed to APIF.

GYRO FAILED
APIF GYRO:

SELECT OTHER

HEADING SENSOR

Caution
B

Gyro connected at

APIF failed.

Check Gyro connect-

ed to APIF.

HCS UNAVAIL.
APIF FAILURE:

CHECK APIF

Caution
B

APIF is not respond-

ing, AP is in standby.

Check APIF.

MAG FAILED
APIF MAGNETIC

HDG FAILED:

CHECK SENSOR

Caution
B

Magnetic compass

connected to APIF

failed.

Check magnetic com-

pass connected to

APIF.

POS FAILED
APIF POSITION

FAILED: CHECK

SENSOR

Caution
B

none

Position sensor con-

nected to APIF failed.

Check position sensor

connected to APIF.

SPD FAILED
APIF SPEED

SENSOR FAILED:

CHECK SPEED

SENSOR

Caution
B

Speed sensor con-

nected to APIF failed.

Check speed sensor

connected to APIF.

Tab. 12: Alerts HDG Control

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

FORCED TO MAN
NO STEERING

MODE: USE MANU-

AL STEERING

Alarm
B

Status of Steering se-

lector switch is not

available.

Use manual steering,

check steering se-

lector switch, check

CAN-BUS.

HCS STOPPED
NO HEADING:

CHECK HEADING

SENSORS

Alarm
B

to BN-

WAS
(30 s)*

No heading informa-

tion available, head-

ing control remains

active but rudder is

frozen.

Use manual steering,

check heading sen-

sors.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды