Quantum ODYSSEY HF Series Скачать руководство пользователя страница 457

Страница: 457 / 493

Appendix D Calibration (Using Generator Service Tools)

Revision W

HF Series X-ray Generators - Service Manual

D-30

Quantum Medical Imaging, LLC

8. If not within tolerance, press Repeat button, re-take the exposure at

same settings and adjust kVp value as necessary. Repeat this step until

indicated and measured kVp values agree to within tolerance. Press the

Confirm button to proceed to next calibration.

9. Take an exposure at the setting indicated on the 100kVp Calibration

Screen (i.e., 100 kVp, 200L mA, 100 msec).

10. On the kVp meter, observe the measured kVp value. Enter the actual

(measured) value by adjusting the slide control, or by selecting the data

entry box and typing the value using a keyboard. The value entered

should be to the hundredths decimal place. Press Calibrate button.

11. Ideally, the value appearing in the 100 kVp Calibration Screen (Step 1.)

will match the reading on the kVp meter within its allowable tolerance. If

so, press the Confirm button. The calibration value is saved and the

system advances to the next calibration procedure.

12. If not the same, press Repeat to re-take exposure and re-enter the mea-

sured kVp value.

13. Repeat kVp calibration for 100 kVp until indicated and measured kVp val-

ues agree to within tolerance. Press Confirm to save calibration value

and to advance to next calibration procedure.

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды