Quantum ODYSSEY HF Series Скачать руководство пользователя страница 389

Страница: 389 / 493

Appendix B Calibration (DiRex System)

Revision W

HF Series X-ray Generators - Service Manual

B-26

Quantum Medical Imaging, LLC

AEC optical density (on systems equipped with AEC option). These procedures

should be performed in the order presented in this chapter. The following is a

brief description of each of the Calibration Menu selections:

•

A/D: Accesses the analog-to-digital (A-D) converters calibration function

•

KV: Accesses KV calibration function

•

Filament: Accesses tube filament offset calibration function

•

MA: Accesses mA calibration function

•

AEC: Accesses the AEC optical density and AEC kVp calibration functions

(active on systems equipped with AEC option only). Note that all of the

AEC Calibrations must be performed for each table and/or film/screen

combination used with the x-ray system. Selection of each film/screen

type used with the system is explained in "CONFIGURATION SETTINGS"

paragraph described previously in this chapter.

•

Back: Returns to the Generator Service Menu. This function is also

provided in each of the above calibration screens, from which you are

returned to the main Calibration Menu

The paragraphs that follow describe the procedures for performing each of the

above calibration functions. Following initial system installation, these procedures

should be performed in the order presented in this chapter.

General Calibration Procedure Notes
The following notes apply in general to all calibration procedures, including

AEC calibration procedures. Please review these notes prior to performing

calibration.
•

Press the Next button to advance to the next calibration procedure.

•

Press the Back button to return to the previous calibration procedure.

•

Each calibration screen displays the correct KV, MA, time and thickness

(in CM) value required for performing a particular calibration procedural

step. However, always ensure the correct values are set prior to

performing each procedural step.

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды