Quantum ODYSSEY HF Series Скачать руководство пользователя страница 381

Страница: 381 / 493

Appendix B Calibration (DiRex System)

Revision W

HF Series X-ray Generators - Service Manual

B-18

Quantum Medical Imaging, LLC

2. The system displays the ION CHAMBER Configuration Screen, as shown

in the example below:

Figure B-12. Ion Chamber Settings Screen

The Ion Chamber Settings Screen displays the assignment of ion chamber

detectors (detector A, B, and C) with respect to the generator’s ion chamber

detector select signals (i.e., FIELD SELECT 1, FIELD SELECT 2 and FIELD

SELECT 3) generated by AEC Control Board A11. That is, assigning "2" to

Field "A" enables detector "2" when the UPPER LEFT chamber detector field is

selected at the Operator Control Panel.
The Ion Chamber Settings Screen also provides settings that facilitate proper

compatibility of the generator with ion chambers that operate differently.

These include Ion Chamber Type (Slope/Level), Polarity (+/-), Output (Nor-

mal/Inverted), and Relay On/Off o settings.
3. Press the Modify button adjacent to the ion chamber detector (Field A,

Field B or Field C) and choose the desired detector setting (1, 2, 3 or

Off).

NOTE: AID ICX-153 or ICX-1153 RIGHT LOAD
USES THIS CONFIGURATION. FOR AID ICX-153
or ICX-1153 LEFT LOAD, SET A=3 AND C=2.

PRESS THESE
BUTTONS TO
MODIFY A
DETECTOR

PRESS TO

SCROLL DOWN

LIST FOR

ADDITIONAL

SETTINGS

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды