manualshive.com logo in svg

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Поделиться
Скачать
Quantum ODYSSEY HF Series Скачать руководство пользователя страница 191

Chapter 5  Service Instructions

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging, LLC

5-7

READY 
LED not 
illuminated

1. Generator Cabinet ON/OFF Cir-

cuit Breakre is OFF.

2. ON/STDBY Rocker Switch on 

OCP (non-Q-Connect Sys-
tems) or Power/Expose Control 
Box (Q-Connect Systems) is set 
to STDBY.

3. Facility electrical has been 

interrupted.

4. Filament automatically shuts off 

after 60 minutes of inactivity.

4. The exposure setting(s) exceed 

the tube or model limits.

5. Faulty communications 

between generator and OCP.

6. Incorrect generator program or 

generator is not working.

7. Lost communication between 

OCP and generator cabinet.

1.Verify that the ON/OFF Circuit 

Breaker on Generator is ON.

2. Set ON/STDBY Rocker Switch on 

OCP (non-Q-Connect Systems) or 
Power/Expose Control Box (Q-
Connect Systems) to ON.

3.  Check, and if possible, reset Facil-

ity electrical service.

4.  Press PREP key. An error mes-

sage displays on the operator con-
trol panel. Refer to appropriate 
error message listed in this table 
for error details. Press any key to 
clear error. System should now be 
ready for exposure.

5.  Non-Q-Connect Systems only: 

Check serial cable connection 
between OCP and generator cabi-
net and jumper settings on OCP 
Control Board (AY40-004S1).

400 Volt 
Anode

See "Line/400V Anode" message

See "Line/400V Anode" message

400 Volt 
Cathode

See "Line/400V Cathode" mes-
sage

See "Line/400V Cathode" message

AC Volt 
Diff

Output by Logic board, indicating 
a hardware failure when a signifi-
cant difference between Anode 
and Cathode voltage is detected.

Note: This error applicable on Q-
Connect Systems only.

Proceed to "KVP Error" and trouble-
shoot accordingly.

ADC
Negative 
15

See "Minus 15V" message

See "Minus 15V" message

ADC
Negative
Reference

See "Vref-" message

See "Vref-" message

Table 5-1.  Error Messages and Possible Cause(s)

Error 

Message

Possible Cause(s)

Remedial Action

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды