Quantum ODYSSEY HF Series Скачать руководство пользователя страница 416

Страница: 416 / 493

Appendix B Calibration (DiRex System)

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging, LLC

B-53

d. Take an exposure at the setting indicated on the AEC Optical Density

Calibration Screen (i.e., 50 kVp, 200L mA, normal density).

e. Process the CR Film Plate to determine density level (referred to as

the "LGM" value).

If the LGM value is within acceptable range of the Target Level as

defined by the CR Film Plate manufacturer, press the Next button to

save the setting and proceed to AEC KV Calibration.

g. If not within range, perform the following adjustments:

Note: If the system is equipped with "standard

type" AEC Board A11 (AY40-031S), the "Table

Gain Adj. Potentiometer" is A11R22 and the "Wall

Gain Adj. Potentiometer" is A11R23. If the sys-

tem is equipped with "Universal type" AEC Board

A11 (AY40-027S), the "Table Gain Adj. Potenti-

ometer" is A11R77 and the "Wall Gain Adj. Poten-

tiometer" is A11R79.

i. Adjust Table Gain Adj. potentiometer (if calibrating the table

receptor) or Wall Gain Adj. potentiometer (if calibrating the

wall receptor), and repeat exposure. Continue until the mea-

sured LGM value equals the Target Level setting to within CR

System manufacturer’s specification.

ii. If you still cannot achieve the Target Level setting, set Table

Gain Adj. potentiometer (if calibrating the table receptor) or

Wall Gain Adj. potentiometer (if calibrating the wall receptor)

to mid-range, then adjust the ion chamber’s MASTER GAIN

potentiometer until roughly the desired LGM is obtained. Fur-

ther fine-tuning can then be achieved by adjusting the Table

or Wall Gain Adj. potentiometer as described in the previous

step.

iii. If the measured LGM value still does not equal the Target

Level setting even with the ion chamber’s MASTER GAIN

potentiometer set to maximum gain position, increase each

chamber detector gain and perform the "AEC MAS Balance

Verification" procedure. Repeat AEC Optical Density calibra-

tion.

iv. If the measured LGM value still does not equal the Target

Level setting after adjusting the MASTER GAIN and gain of

individual detectors, reduce the AEC Reference until you

obtain the desired LGM value.

3. If the selected film/screen combination is not the first one to be cali-

brated with the system, perform the following steps:

NOTE

The series of

AEC optical

density

measurements

should be

repeated as

many times as

required until

optical density

is sufficiently

accurate to

meet

regulatory and

facility

requirements.

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды