Quantum ODYSSEY HF Series Скачать руководство пользователя страница 137

Страница: 137 / 493

Chapter 3 Calibration

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging, LLC

3-45

7. Verify 400L MA appears in the center display box and Measure, Cali-

brate appears in the top right field.

8. Take an exposure at the setting indicated in the center display box (i.e.,

60 kVp, 400L mA, 100.0 mS).

9. On the Dynalyzer Digital Display or on mAs meter, observe the measured

mA value. (Ideally, this value should be 400 mA or 40 mAs.)

10. If not 400 mA, adjust the value in the Measure MA#2 field up or down

by pressing the key next to the up or down arrow, respectively, until the

Measure MA#2 field is set to the value displayed on the kVp meter.

Each time the key is pressed changes the MA value up/down in one-tenth

increments.

11. Press key next to the Save Calibrate field to save the 75S and 400L mA

calibration entries. The MA Calibration Menu (First Measure) should be

displayed.

12. Take 60 kVp, 75S mA, 100 ms and 60 kVp, 400L mA, 100 ms exposures.

The measured kVp values should correspond with the indicated kVp set-

tings within 3% tolerance; and the measured mA values should corre-

spond with the indicated mA settings at least within 4%+1 mA. If not,

repeat kVp and/or mA calibration as described in the previous para-

graphs.

Note: The Power Supply Board’s +48 VDC output

may require adjusting (using potentiometer

A6R17) up to +55 VDC (max.) in cases where

long-length high tension cables are used and/or a

heavy duty x-ray tube is installed. This can be

determined by measuring the mA output (using a

Dynalyzer or mAs meter), of an exposure taken at

40 - 50 kVp and the highest mA station available.

The mA measured should be the same as the indi-

cated mA (within specified tolerance). If mA out-

put is too low, increase the +48 VDC voltage

output as required, but do not 55 VDC.

13. If the system is equipped with QG-AEC option, perform AEC Calibration

procedures. Otherwise, calibration is complete. To return to the Service

Calibration screen, press the key next to the Main field.

CAUTION! If using a mAs meter, re-connect the

green/yellow wire marked "MAS METER" to the

ground stud on top of the H.V. Transformer (see

Figure 3-32).

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды