Quantum ODYSSEY HF Series Скачать руководство пользователя страница 361

Страница: 361 / 493

Revision W

HF Series X-ray Generators - Service Manual

A-14

Quantum Medical Imaging, LLC

Appendix A AEC Calibration with DR or CR Film Plate

(refer to manufacturer’s installation and calibration documentation

supplied with DR system) with the AEC REF value appearing in AEC

Optical Density Calibration screen shown above.

8. Set the ion chamber detector selection to middle detector and ensure

x-ray tube is at correct SID. Ensure the ion chamber has been bal-

anced.

9. Verify the Optical Density field is set to the desired optical density

(e.g., "1.30"). If not, press the up or down key located next to the

Optical Density field until the "base" optical density setting is equal

to the desired optical density (1.30 in this example).

Do not change

the optical density setting at any time during this procedure.

10. Place 5 cm of acrylic in the X-ray beam.
11. On AEC Control Board AY40-031S, adjust ion chamber MASTER GAIN

potentiometer A11R22, A11R23, and A11R24 to midrange.

12. Take an exposure at the setting indicated in the center display box

(i.e., 50 kVp, 200L mA).

13. Determine the sensitivity value (sometimes referred to as the "REX"

or "S" value, depending on DR system manufacturer).
a. If the sensitivity value is within acceptable range as defined by

the digital receptor manufacturer, continue at step 14.

b. If not within range, adjust the associated ion chamber’s MASTER

GAIN potentiometer and repeat exposure. Continue until the sen-

sitivity ("REX" or "S") value is acceptable. Note the sensitivity

value as it will be needed in a later step.

14. Move the DR receptor to the other receptor cabinet (it’s ion chamber

should be connected to WALL#2 connector A11J3 on AEC Control

Board) and collimate down to proper image size.

15. With 5 cm of acrylic in the X-ray beam, take an exposure at the set-

ting indicated in the center display box (i.e., 50 kVp, 200L mA).

16. Determine the sensitivity value (sometimes referred to as the "REX"

or "S" value, depending on DR system manufacturer).

17. If necessary, adjust the ion chamber’s MASTER GAIN potentiometer

and repeat exposure until the sensitivity ("REX" or "S") value is the

same as the value obtained for the previously calibrated ion chamber

in step 13b.

Note: If later on it becomes necessary to adjust

the optical density of either receptor’s ion cham-

ber, this should be done by adjusting potentiome-

ter A11R23 on the AEC Control Board, and if

further adjustment is needed, increasing or

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды