Quantum ODYSSEY HF Series Скачать руководство пользователя страница 263

Страница: 263 / 493

Chapter 5 Service Instructions

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging, LLC

5-79

a. Install three (3) OCP Interface Board A1A1 mounting stand-

offs on Logic Board A1 in same locations from which they

were removed.

b. Place the OCP Interface Board A1A1 on mounting standoffs

and secure using one (1) screw and two (2) hex nuts.

c. Connect ethernet cables to the OCP Interface Board A1A1

connectors J1 and J5.

3. Connect all cables to Logic Board A1. Remove tags.

Note: When installing IC's, ensure that pin one on the

chip is aligned correctly with pin 1 on the IC socket

mounted on the board. Do not use software label to

orient IC!

4. Insert Logic Master IC U9 (marked "QLBM") into U9 socket on

Logic Board A1.

5. Insert the Logic Slave IC U14 (marked "QLBS") into U14 socket

on Logic Board A1.

6. On Logic Boards revision G and higher, verify jumpers JP1, JP6,

and JP7 are configured as follows:
a. Jumper JP1 - must always be installed
b. Jumper JP6 - installed only if system is equipped with high-

speed starter (QG-HSS) option. Do not install on standard,

single-speed rotor systems (i.e., systems equipped with Rotor

Drive Board A10 AY40-013T).

c. Jumper JP7 - install jumper on pins 2-3

7. Set the ON/OFF circuit breaker CB1 on the generator cabinet to

ON position.

8. Set the power on/standby switch on the Operator Control Panel

(OCP) to the on ( ) position.

9. Verify generator passes startup self-tests.
10. Access Service Mode, Service Configuration and Settings screens,

and verify generator configuration settings are correct.

11. Access Service Mode, AD Calibration screen. Verify all voltages

are within tolerance. If not, calibrate in accordance with "A/D

Calibration Procedure" in Chapter 3 (ODYSSEY) or Appendix B

(DiRex Integration generators), or Appendix D (all other inte-

grated generators).

12. Spot check kVp and mA calibration and, if needed, re-calibrate

system.

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды