Quantum ODYSSEY HF Series Скачать руководство пользователя страница 234

Страница: 234 / 493

Chapter 5 Service Instructions

Revision W

HF Series X-ray Generators - Service Manual

5-50

Quantum Medical Imaging, LLC

6. Upon validation of the password, the Service Mode Menu dis-

plays. Press the key next to the Reports field. The Service

Reports Menu displays:

Figure 5-1. Service Reports Menu

The Service Reports Menu provides access to various types of system

information. The following briefly describes the various Service Report

Menu selections:

•

Generator Report: Provides total exposure count, average kV and

mA exposure settings, and the total time of all exposures taken on

generator.

•

Last 100 Exposures Report: Provides a chronological listing of the

last 100 exposures. Each exposure (event) can be viewed showing

the time and date the exposure occurred, and the exposure settings

(i.e., kVp, mA, time, AEC on/off status, and receptor selected). The

Next Error and Previous Error keys are used to "scroll" up or

down through the exposure report.

•

Tube Report: Provides total exposure count, average kV and mA

exposure settings, and the total time of all exposures taken on

currently installed x-ray tube.

•

Errors & Warnings Report: Provides a chronological listing of up to

100 error and/or warning messages. Each error or warning message

(event) can be viewed showing the event name, the time and date

the event occurred, and the exposure settings at the time the event

occurred. The Next Error and Previous Error keys are used to

"scroll" up or down through the exposure report.

•

Diagnostic: Not functional at time this manual was printed.

•

Checksums: Displays the software revision levels and checksums of

OCP Control Board A16A1 (AY40-004S1) Microcontroller U3 (referred

to as "Internal" program) and Flash Memory U2 ("External" program

and "Database").

THIS KEY
FOR
FACTORY
USE ONLY

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды