manualshive.com logo in svg

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Поделиться
Скачать
Quantum ODYSSEY HF Series Скачать руководство пользователя страница 167

Chapter 4  Theory of Operation

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging

4-3

OVERVIEW

The following paragraphs provide theory of operation for ODYSSEY HF Series

TM

 Gener-

ators.  Each circuit description references a functional block diagram contained in 

Chapter 6, Diagrams.

OPERATOR CONTROL PANEL CIRCUIT

NOTE: If the generator is configured with the "Q-

Connect option" as in a Q-VISION equipped sys-

tem, or if the generator is integrated to an exter-

nal imaging system’s workstation computer for

operation as the generator’s operator control

panel - refer to Appendix B, CALIBRATION (Agfa

DiRex)  or  Appendix  D,  CALIBRATION  (Using

Insight) for configuration and calibration instruc-
tions. The following circuit description does not

apply to generators equipped with Q-Connect

option.  

The Operator Control Panel Circuit controls the X-ray generator’s exposure set-

tings and exposure sequence, and controls the display of settings on the Front 

Panel liquid crystal display (LCD).  Exposure setting data is input to the Operator 

Control Panel Circuit through the Front Panel key switches.  The READY, PREP, 

and EXPOSE LEDs located on the Front Panel are used to indicate the status of 

the exposure sequence.   The Operator Control Panel Circuit includes an RS-232 

service connection, which allows service personnel to download data to Flash 

Memory, perform X-ray generator diagnostics, and to upload non-volatile random-

access memory (NVRAM) settings.

Microcontroller U3 Operation
Microcontroller U3 is the primary controller of Operator Control Panel Circuit 

functions.  It has it own internal read-only memory (ROM) and random-

access memory (RAM).  The 32 MHZ output from Oscillator U18 provides the 

clocking input to drive Microcontroller U3.  The Reset Circuit U1 monitors the 

+5 VDC supply voltage; when it falls below +4.5 VDC, Microcontroller U3 is 

placed in the "reset state".  When the voltage returns to a level above 4.5 

VDC, the Microcontroller restarts.
Data is sent to the generator via a 9-pin connector and cable connected to 

the generator Logic Board.  The 9-pin cable includes RS-485 communication, 

hardware control lines, and power supply voltage from the generator.  PREP 

and EXPOSE hardware lines are routed from Open Collector Driver U16 to the 

generator to indicate the state of the system to the generator.
Flash Memory U2
Flash Memory U2 holds part of the main program and all of the tables for the 

LCD display screens.  Flash Memory is accessed by Microcontroller U3 

through the DATA/ADDRESS bus and Control Signals.  On the first memory 

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды