manualshive.com logo in svg

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Поделиться
Скачать
Quantum ODYSSEY HF Series Скачать руководство пользователя страница 176

Chapter 4  Theory of Operation

Revision W

 HF Series X-ray Generators - Service Manual

4-12

Quantum Medical Imaging

POWER SUPPLY CIRCUIT

The power supply circuit (see Power Supply Board A6 (AY40-005T) Schematic 

Diagram in Chapter 6, DIAGRAMS) consists of four power supplies that provide 

the power needed to the control circuits.  Two power supplies (+15VDC and 

+48VDC) are switching power supplies.  The other two power supplies (+24VDC 

and -15VDC) are linear.

+48 VDC Power Supply
The +48 VDC and +15 VDC power supplies work with the same boost con-

cept design, but some of the components are different between the power 

supplies.
The +48 VDC Power Supply consists of Bridge Rectifier DB1 that produces a 

43 VDC (approximately) output (TP2), which is filtered by capacitor C2.  The 

43 VDC is chopped by transistor Q1 with inductor L1 in series.  When Q1 

turns off, the inductor and the DC voltage across C2 supplies voltage to the 

output.  The output is the sum of both voltages.  Therefore, the output volt-

age will never be lower than

 

+43 VDC (neglecting the voltages across compo-

nents).  The time that transistor Q1 is on depends on the input DC voltage 

and the output load.  Pulse-Width Modulator (PWM) U1 samples the output 

voltage, and it controls Q1 on time to maintain constant output voltage.  The 

output voltage is adjusted to +48 VDC (TP3) with R17 in case there is a prob-

lem supplying the filament current as a result of long length high-voltage 

(H.V.) cables.  The +48 VDC output can be adjusted to supply adequate fila-

ment current.  The maximum adjusted voltage should not 52 VDC.
+15 VDC Power Supply
The +15 VDC power supply works using the same boost concept design as 

the +48 VDC power supply.  The +15 VDC Power Supply bridge rectifier DB4 

produces a DC voltage output, which is filtered by capacitor C18.  The DC 

voltage should be approxi13 VDC (TP10).  The DC voltage is 

chopped by transistor Q2 with inductor L2 in series.  When the transistor 

turns off, the inductor and the DC voltage across C18 supplies voltage to the 

output.  The time that transistor Q1 is on depends on the input DC voltage 

and the output load.  PWM U2 samples the output voltage, and it controls Q2 

on time to maintain constant output voltage.  The output of the +15 VDC 

supply has a resettable fuse (F2).  When the load exceeds the limit of the 

fuse, the output shuts off until the overload is removed.
+24 VDC Power Supply
The +24 VDC power supply uses a linear adjustable regulator that produces 

regulated 24VDC (at TP8).  The input DC voltage (approximately 35V) to the 

regulator comes from bridge rectifier DB4 and filter capacitor C15.
The power supply that produces the -15VDC uses a linear fix output regulator 

that produces the regulated -15VDC (TP8). The input negative DC voltage 

(TP7 approximately -21V) to the regulator comes from the bridge rectifier 

DB2 and filter capacitor C13.

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды