Quantum ODYSSEY HF Series Скачать руководство пользователя страница 149

Страница: 149 / 493

Chapter 3 Calibration

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging, LLC

3-57

8. If the selected film/screen combination is the first one to be cali-

brated with the system (if so, it should be combination having slow-

est speed and/or largest SID), perform the following steps:
a. Verify the AEC Ref field is set to 2000. If not, use the up and

down keys next to the AEC Ref field to set the AEC Ref value to

"2000".

b. If not already done so, set the Optical Density value to the

desired film optical density value (for example, 1.30).

c. Place 5 CM of acrylic in the X-ray beam. Take an exposure at the

setting indicated in the center display box (i.e., 50 kVp, 200L mA).

d. Develop film and measure optical density using a calibrated den-

sitometer.

e. If the system is equipped with AEC Board A11 part number

AY40-031S, proceed as follows:

i. If the measured optical density corresponds with base optical

density setting, press the Next Calibrate key to save the

setting and proceed to Reciprocity Calibration. If not, adjust

potentiometer A11R22 (if calibrating the table receptor) or

A11R23 (if calibrating the wall receptor), and repeat expo-

sure. Continue until the measured optical density equals the

base optical density setting (at least to within 5% of base

optical density setting).

ii. If the measured optical density still does not equal the Base

Optical Density setting, set A11R22 or A11R23 to mid-range,

then adjust the ion chamber’s MASTER GAIN potentiometer

until roughly the desired optical density of film is obtained.

Further fine-tuning can then be achieved by adjusting potenti-

ometer A11R22 (table) or A11R23 (wall) as described in the

previous step.

NOTE: If the measured optical density still does

not equal the Base Optical Density setting even

with the ion chamber’s MASTER GAIN potentiome-

ter set to maximum gain position, increase each

chamber detector gain and perform the "AEC MAS

Balance Verification" procedure. Repeat AEC Opti-

cal Density calibration. If the measured optical

density still does not equal the Base Optical Den-

sity setting after adjusting the MASTER GAIN and

gain of individual detectors, reduce the AEC Refer-

ence until you obtain the desired optical density.

f. If the system is equipped with AEC Board A11 part number

AY40-027S, proceed as follows:

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды