manualshive.com logo in svg

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Поделиться
Скачать
Quantum ODYSSEY HF Series Скачать руководство пользователя страница 154

Chapter 3  Calibration

Revision W

 HF Series X-ray Generators - Service Manual

3-62

Quantum Medical Imaging, LLC

AEC KV Calibration Procedure
The AEC KV Calibration screen, shown below, is used to calibrate the tube 

voltage to the "base optical density" setting. There are a total of six kV 

calibration points for a 125 kV system (50, 60, 80, 100, 110, and 120 kV); 

150 kV systems require an additional two kV calibration points (130 and 

140 kV).  The image receptor and chamber field settings remain the 

same as those used in the Reciprocity Calibration procedure.

Figure 3-41.  AEC KV Calibration Screen

Proceed as follows:
1. Place indicated thickness of acrylic (5 CM for first calibration point) in 

the X-ray beam.

2. Place a film cassette in the tray and collimate down to film size.
3. Verify the receptor in which the film cassette is inserted is selected as 

indicated on the AEC KV Calibration screen.

4. Take an exposure at the setting indicated in the center display box 

(i.e., 50 kVp, 200L mA).

5. Develop the film and measure the optical density using a calibrated 

densitometer.

6. Press the up or down key located next to the Measured OD field 

until the optical density value displayed equals the measured optical 

density value (the Measured OD up arrow key increases the optical 

density value and the Measured OD down arrow key decreases the 

optical density value).  DO NOT TAKE ANY FURTHER EXPOSURES AT 

THIS SETTING.

7. Press the key next to the Measure OD field to save the first kV cali-

bration point entry (50 kV, 5 CM). The AEC KV Calibration screen is 

updated for the next kV calibration point (60 kV, 10 CM).

BASE 
OPTICAL 
DENSITY 
SETTING

MEASURED 
OPTICAL 
DENSITY 
KEYS

KVP MEASURE 
SELECT FIELD

 

NOTE

Calibration of the 
first step (50 kVp) 
is not required as 
long as AEC 
Optical Density 
Calibration 
procedure in the 
previous steps 
was performed 
prior to AEC KV 
Calibration. A 
verification that 
the "Measured 
OD" is the same 
as the "Optical 
Density" setting is 
all that is 
required.

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды