Quantum ODYSSEY HF Series Скачать руководство пользователя страница 157

Страница: 157 / 493

Chapter 3 Calibration

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging, LLC

3-65

4. The Copy/Film Screen screen appears:

Figure 3-42. Copy Film/Screen Screen

5. Press the key next to the "From" field until the name of the film/

screen combination from which calibration data will be copied

appears.
CAUTION! Before proceeding, check to make sure

the "from" and "to" film/screen copy selections are

correct. Selecting Copy Film/Screen as directed in

the next step causes existing calibration data for the

film/screen being copied "to" to be overwritten with

calibration data of the "from" film/screen.

6. Press the key next to the Copy Film/Screen field. All AEC calibra-

tion data is now copied from the Wall 40" film/screen combination to

the Table 40" film/screen combination. To abort without copying,

press the key next to the MAIN field. The AEC Calibration Menu is

displayed.
IMPORTANT NOTES:

1. Upon completing calibration procedures, it is

recommended that the Q-Ware program be used

to upload calibration data (and APR technique

data, if APR editing was performed) as a backup

in case a problem occurs that requires re-calibra-

tion of the generator. To obtain a copy of the Q-

Ware program, contact Quantum Medical Imag-

ing’s Customer Service Department.

2. Be sure to only use calibrated film/screens in

all programmed APR procedures. If the APR

default film screen is different than the calibrated

film screen, the procedure must be edited to use

the calibrated film screen.

PRESS THIS KEY
TO SELECT THE

FILM/SCREEN

TO COPY

CALIBRATION

DATA FROM

DISPLAYS

DESTINATION

FILM/SCREEN

NAME

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды