Quantum ODYSSEY HF Series Скачать руководство пользователя страница 419

Страница: 419 / 493

Appendix B Calibration (DiRex System)

Revision W

HF Series X-ray Generators - Service Manual

B-56

Quantum Medical Imaging, LLC

5. Process the CR Film Plate to determine the density level (referred to as

the "LGM" value).
a. If the sensitivity value is within acceptable range as defined by man-

ufacturer, press the First Point button to proceed to the next AEC kV

calibration point.

a. If not within range, press the Measured Level value button (located

directly below "Measured Level" label), and enter the measured LGM

value using the keypad, then press Enter. Press First Point button

to proceed to the next AEC kV calibration point.

DO NOT TAKE ANY

FURTHER EXPOSURES AT THIS SETTING.

6. Repeat the previous steps for the 60, 80, 100, 110, 120, and, if 150 kV

system, 130 and 140 kV calibration points, placing the specified thickness

of acrylic in the x-ray beam as indicated on the AEC KV Calibration screen

for each kV calibration point, and taking one exposure per kVp calibration

point until all the measured density (LGM) values are within required

range.

7. Press the Back button to return to the AEC Calibration menu.
8. This completes AEC calibration for this particular film/screen combination.

Repeat AEC calibration procedures for all additional film/screen combina-

tions that will be used with the system.

9. Verify AEC calibration by taking several exposures in AEC mode and

checking the resulting "LGM" value. If necessary, repeat AEC calibration

procedure to further adjust AEC accuracy.

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды