Qiagen QIAcube Connect MDx Скачать руководство пользователя | Manualshive

Страница: 26 / 155

background image

QIAcube Connect MDx User Manual 12/2020

26

USB ports

The QIAcube Connect MDx has four USB ports. Two are located on the left of the touchscreen and
two are located behind the touchscreen.

The USB ports located on the left of the touchscreen allow connection of the QIAcube Connect MDx
to a USB flash drive. Data files, such as support package, protocols or report files, can be
transferred via the USB port from the QIAcube Connect MDx to the USB flash drive. The USB ports
can also be used to plug in the supplied external barcode scanner.

USB ports located below the touchscreen, allow insertion of a Wi-Fi adapter to enable Wi-Fi
connection to a local network.

Important

: Use only the USB flash drive provided by QIAGEN. Do not connect other USB flash

drive devices to USB ports.

Important

: Do not remove the USB flash drive while downloading or transferring data or software

to or from the instrument.

Important

: Always turn off the QIAcube Connect MDx in order to plug or unplug the

Wi-Fi USB device. Plug-and-play of the Wi-Fi USB device while the instrument is turned on is
not supported.

Waste drawer

Used disposable filter-tips are discarded through two slots in the worktable and collected in the
waste drawer. Used columns (e.g., QIAshredder columns) are also discarded into this drawer.

CAUTION

Damage to the instrument

[C3]

Empty the tip disposal container prior to use to prevent a tip jam in the waste
drawer. Failure to empty the waste container may block the robotic arm that
could cause run failure or instrument damage.

WARNING

Hazardous chemicals and infectious agents

[W16]

The waste may contain toxic material and must be disposed of properly. Refer
to your local safety regulations for proper disposal procedures.

«
...
24
25
26
27
28
...
»

Содержание QIAcube Connect MDx




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для QIAcube Connect MDx

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 15

Бренд: Garelick Страницы: 2

Бренд: Garelick Страницы: 2

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: York Fitness Страницы: 36

Бренд: Park House Healthcare Страницы: 12

Бренд: Labnet Страницы: 12

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Бренд: M-Audio Страницы: 25

LED PowerBank 48

Бренд: SHOWTEC Страницы: 12

Бренд: ASIA TECHNOLOGY Страницы: 38

Бренд: TaiShan Страницы: 5

Бренд: Almat Страницы: 4

Бренд: ITEM Страницы: 12

Бренд: Shel lab Страницы: 32

Бренд: Kellfri Страницы: 24

V-M.O.L.E. Solar

Бренд: ECD Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды