Qiagen QIAcube Connect MDx Скачать руководство пользователя | Manualshive

Страница: 28 / 155

background image

QIAcube Connect MDx User Manual 12/2020

28

WARNING

Electrical hazard

[W8]

Any interruption of the protective conductor (earth/ground lead) inside or
outside the instrument or disconnection of the protective conductor terminal is
likely to make the instrument dangerous.

Intentional interruption is prohibited.

Lethal voltages inside the instrument

When the instrument is connected to line power, terminals may be live and
opening covers or removing parts is likely to expose live parts.

WARNING

Damage to electronics

[W9]

Before powering ON the instrument, make sure that the correct supply voltage
is used.

Use of incorrect supply voltage may damage the electronics.

To check the recommended supply voltage, refer to the specifications
indicated in the type plate of the instrument.

WARNING

Risk of electric shock

[W10]

Do not open any panels on the QIAcube Connect MDx.

Risk of personal injury and material damage

Only perform maintenance that is specifically described in this user manual.

Cooling air outlet

Cooling air outlets are located at the rear left side of the QIAcube Connect MDx and allow cooling
of the internal components of the QIAcube Connect MDx.

CAUTION

Risk of overheating

[C9]

To ensure proper ventilation, maintain a minimum clearance of 10 cm at the
sides and rear of the QIAcube Connect MDx.

Slits and openings that ensure the ventilation of the QIAcube Connect MDx
must not be covered.

«
...
26
27
28
29
30
...
»

Содержание QIAcube Connect MDx




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для QIAcube Connect MDx

Бренд: York Fitness Страницы: 34

Бренд: Zetec Страницы: 23

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: York Страницы: 26

Бренд: V-TAC Страницы: 13

Бренд: Xtool Страницы: 8

Бренд: Hammer Strength Страницы: 8

Quadro A Legs 3P 120 Degree Workstation with...

Бренд: Jason.L Страницы: 10

Бренд: Meritor Страницы: 65

Бренд: Bavis Страницы: 8

Бренд: AGCO Страницы: 44

Aesculap S4 FW103R

Бренд: Braun Страницы: 39

Бренд: Heitronic Страницы: 8

Бренд: Eurotops Страницы: 8

Бренд: KRATOS SAFETY Страницы: 36

TRACER pH PockeTester 1741

Бренд: LaMotte Страницы: 16

Бренд: Psiber Страницы: 16

ANY SPOT AS-1400-2P

Бренд: Galaxy Audio Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды