Qiagen QIAcube Connect MDx Скачать руководство пользователя

Страница: 17 / 155

QIAcube Connect MDx User Manual 12/2020

CAUTION

Damage to the instrument

[C8]

After a power failure, do not move the z-module (robotic arm) manually in
front of the instrument. Damage may occur if the QIAcube Connect MDx hood
is closed and collides with the z-module.

WARNING

Risk of personal injury and material damage

[W20]

Raise the centrifuge lid carefully. The lid is heavy and may cause injury if it
falls.

CAUTION

Risk of overheating

[C9]

To ensure proper ventilation, maintain a minimum clearance of 10 cm at the
sides and rear of the QIAcube Connect MDx.

Slits and openings that ensure the ventilation of the QIAcube Connect MDx
must not be covered.

2.8

Heat hazard

The QIAcube Connect MDx worktable contains a heated shaker.

WARNING

Hot surface

[W21]

The shaker can reach temperatures of up to 70°C (158°F). Avoid touching it
when it is hot. Carefully remove the samples after a run.

2.9

Maintenance safety

WARNING/

CAUTION

Risk of personal injury and material damage

[W22]

Only perform maintenance that is specifically described in this user manual.

Содержание QIAcube Connect MDx




























































































































































Результаты поиска

Содержание QIAcube Connect MDx

Отзывы:

Похожие инструкции для QIAcube Connect MDx

Бренды по названию

Популярные бренды

Qiagen QIAcube Connect MDx, Руководство пользователя

Результаты поиска

Содержание QIAcube Connect MDx

Отзывы:

Похожие инструкции для QIAcube Connect MDx

Бренды по названию

Популярные бренды