Qiagen QIAcube Connect MDx Скачать руководство пользователя | Manualshive

Страница: 107 / 155

background image

QIAcube Connect MDx User Manual 12/2020

107

6

Cleaning and Maintenance

WARNING/

CAUTION

Risk of personal injury and material damage

[W22]

Only perform maintenance that is specifically described in this user manual.

Important

: The following maintenance procedures must be carried out to ensure reliable operation

of the QIAcube Connect MDx:



Regular maintenance: after

each

protocol run



Daily maintenance: after the last protocol run of the day



Monthly maintenance: every month



Periodic maintenance: when necessary; at least every 6 months

Optionally, these procedures may be performed to check and ensure the reliability of operation of
the QIAcube Connect MDx:



UV Run: reduces pathogen and nucleic acid contamination



Tightness Test: ensures the tightness of the tip adapter (e.g., after O-Ring change)

The software provides step-by-step guidance under

Tools/Maintenance

for the maintenance

procedures listed above, except for the regular maintenance.

Following these procedures ensures that the QIAcube Connect MDx is free from dust and liquid
spills.

Select the cleaning agent according to the objective of the cleaning procedure, the sample material
used and the downstream assay.

WARNING

Risk of fire or explosion

[W6]

When using ethanol or ethanol-based liquids on the QIAcube Connect MDx,
handle such liquids carefully and in accordance with the required safety
regulations. If liquid has been spilled, wipe it off and leave the QIAcube
Connect MDx hood open to allow flammable vapors to disperse.

Before using any cleaning or decontamination methods except those recommended by the
manufacturer, users should check with the manufacturer that the proposed method will not damage
the equipment.

«
...
105
106
107
108
109
...
»

Содержание QIAcube Connect MDx




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для QIAcube Connect MDx

Бренд: Jacobs Ladder Страницы: 16

Бренд: Halyard Страницы: 88

Бренд: Agilent Technologies Страницы: 114

Бренд: Lencarta Страницы: 6

Бренд: Focal Meditech Страницы: 10

Бренд: Rohm Страницы: 17

Бренд: Hameg Страницы: 39

Бренд: Teac Страницы: 1

Бренд: Garelick Страницы: 2

Бренд: Eurotops Страницы: 8

Бренд: KRATOS SAFETY Страницы: 36

Бренд: ultraMEDIC Страницы: 28

Бренд: Evermed Страницы: 16

Бренд: Enerpac Страницы: 36

NOVACAT X8 COLL

Бренд: Pottinger Страницы: 91

accumet BASIC AB 15

Бренд: Fisher Scientific Страницы: 56

Бренд: Specac Страницы: 43

Бренд: Xantech Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды