Qiagen QIAcube Connect MDx Скачать руководство пользователя | Manualshive

Страница: 149 / 155

background image

QIAcube Connect MDx User Manual 12/2020

149

QIAcube Connect, Installation

On-site installation and setup of instrument hardware and system
software. Training demonstrating routine maintenance, basic
troubleshooting, and more for up to 4 laboratory staff members.

9245211

Starter Pack, QIAcube

200 µl filter-tips (1024); 1000 µl filter-tips (1024); 30 ml reagent
bottles (12); rotor adapters (240); 1.5 ml elution tubes (240); rotor
adapter holder (1)

990395

QIAcube Connect IQ/OQ

On-site installation qualification and operational quality service.

9245232

Accessories

Filter-Tips, 1000 µl (1024)

Disposable Filter-Tips, racked; (8 x 128)

990352

Filter-Tips, 1000 µl, wide-bore
(1024)

Disposable Filter-Tips, wide-bore, racked; (8 x 128); not required for
all protocols

990452

Filter-Tips, 200 µl (1024)

Disposable Filter-Tips, racked; (8 x 128); not required for all protocols

990332

Rotor, centrifuge

Rotor for the QIAcube centrifuge

9017848

Swing-out Buckets

Swing-out buckets for the rotor of the QIAcube centrifuge

9017849

Rotor Adapters (10 x 24)

For 240 preps: 240 Disposable Rotor Adapters and 240
microcentrifuge tubes (1.5 ml); for use with the QIAcube Connect
MDx

990394

Rotor Adapter Holder

Holder for 12 disposable rotor adapters; for use with the QIAcube
Connect MDx

990392

«
...
147
148
149
150
151
...
»

Содержание QIAcube Connect MDx




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для QIAcube Connect MDx

Бренд: QBC Diagnostics Страницы: 65

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: Kärcher Страницы: 88

Бренд: National Instruments Страницы: 10

Бренд: Elenco Electronics Страницы: 12

Бренд: GRAVITY Страницы: 2

Alcotest 7410 GLC

Бренд: Dräger Страницы: 15

Бренд: enz Страницы: 40

Magnetic Rail System Premium

Бренд: Geovent Страницы: 12

DL-FLEXILED100W/B

Бренд: Techni-Lux Страницы: 12

Бренд: Laversab Страницы: 103

Бренд: Titan Fitness Страницы: 7

Бренд: Sentinel Страницы: 16

18 Liter/30 Cans Sport Fridge with AM/FM radio

Бренд: Wagan Страницы: 4

Бренд: Salamander Designs Страницы: 4

Бренд: Facom Страницы: 2

Бренд: NICOR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды