Qiagen QIAcube Connect MDx Скачать руководство пользователя | Manualshive

Страница: 40 / 155

background image

QIAcube Connect MDx User Manual 12/2020

40

WARNING

Electrical hazard

[W8]

Any interruption of the protective conductor (earth/ground lead) inside or
outside the instrument or disconnection of the protective conductor terminal is
likely to make the instrument dangerous.

Intentional interruption is prohibited.

Lethal voltages inside the instrument

When the instrument is connected to line power, terminals may be live and
opening covers or removing parts is likely to expose live parts.

4.1.3

Grounding requirements

To protect operating personnel, the National Electrical Manufacturers’ Association (NEMA)
recommends that the QIAcube Connect MDx be correctly grounded (earthed). The instrument is
equipped with a 3-conductor AC power cord that, when connected to an appropriate AC power
outlet, grounds (earths) the instrument. To preserve this protection feature, do not operate the
instrument from an AC power outlet that has no ground (earth) connection.

WARNING

Electrical hazard

[W8]

Any interruption of the protective conductor (earth/ground lead) inside or
outside the instrument or disconnection of the protective conductor terminal is
likely to make the instrument dangerous.

Intentional interruption is prohibited.

Lethal voltages inside the instrument

When the instrument is connected to line power, terminals may be live and
opening covers or removing parts is likely to expose live parts.

4.2

Unpacking the QIAcube Connect MDx

WARNING

Risk of personal injury and material damage

[W2]

The QIAcube Connect MDx is too heavy to be lifted by one person. To
avoid personal injury or damage to the instrument, do not lift the instrument
alone.

1.

Before unpacking the QIAcube Connect MDx, move the package to the site of installation and
check that the arrows on the package point upward. In addition, check whether the package
is damaged. In case of damage, contact QIAGEN Technical Service.

2.

Open the top of the transportation box to remove the

QIAcube Connect MDx Quick-Start

Guide,

barcode scanner,

and power cord before lifting the box.

«
...
38
39
40
41
42
...
»

Содержание QIAcube Connect MDx




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для QIAcube Connect MDx

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: UNIA Страницы: 62

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: Haaga Страницы: 31

Бренд: Taurus Страницы: 24

Бренд: Varytec Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды