Qiagen QIAcube Connect MDx Скачать руководство пользователя | Manualshive

Страница: 129 / 155

background image

QIAcube Connect MDx User Manual 12/2020

129

Comments and suggestions

Error displayed when inserting the
USB flash drive into a Windows
PC

Ignore the message. In most cases, no scan is needed;
use the USB flash drive as usual. Do not reformat the
USB on the Windows PC. This will lead to complete data
loss on the USB flash drive, and it can no longer be used
with the QIAcube Connect MDx.

7.3.1

Protocol interruption

If an error occurs during a protocol run, it is possible to continue sample preparation manually.

Important

: It is not recommended for QIAGEN DSP/IVD protocols to finish the run manually, the

run will be invalid and the sample result from the manual continuation of the protocol must not be
used for diagnostic purposes. It is under your responsibility to continue sample processing manually,
as this invalidates the whole procedure.

To continue sample processing:

1.

Note the step at which the protocol stopped. This is displayed in the touchscreen under

Run

Details

.

2.

Remove the samples and reagents from the QIAcube Connect MDx.

3.

Refer to the appropriate protocol in the relevant kit handbook and continue sample processing
manually.

7.3.2

Centrifuge

Opening the centrifuge lid in the event of a breakdown

In case of power failure, the centrifuge lid can be manually opened so that the samples can be
removed. To open the centrifuge lid, follow the instructions below.

WARNING

Moving parts

[W19]

In case of breakdown caused by power failure, remove the power cord and
wait 10 minutes before attempting to manually open the centrifuge lid.

WARNING

Risk of personal injury and material damage

[W20]

Raise the centrifuge lid carefully. The lid is heavy and may cause injury if it
falls.

«
...
127
128
129
130
131
...
»

Содержание QIAcube Connect MDx




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для QIAcube Connect MDx

Бренд: Oberheim Страницы: 40

Бренд: JB-Lighting Страницы: 40

Бренд: Danfoss Страницы: 106

Бренд: Datalogic Страницы: 48

Бренд: PageFlip Страницы: 32

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

Бренд: Haag-Streit Страницы: 16

Бренд: Pani Страницы: 12

Бренд: FASTER TOOLS Страницы: 19

Бренд: Hammer Strength Страницы: 8

Бренд: ABB Страницы: 106

Бренд: RAM Страницы: 4

Бренд: ATD Tools Страницы: 7

SPLICE-500 MKII

Бренд: Serpent Страницы: 8

Бренд: Wecan Technology and Lighting Co., Ltd Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды