Printronix P6000L Скачать руководство пользователя страница 36

Страница: 36 / 234

Operation

2-16

Paper Stacking - Floor Cabinet Models

The floor cabinet model is capable of stacking up to one complete box of standard computer

paper when the paper is properly loaded. After loading the paper, perform the following inĆ

structions.

Open the rear cabinet door to access the paper stacking area.

NOTE: Steps 2 and 3 pertain to installation of the two paper stacking fences, the front

fence between the paper stack and the paper supply and the rear fence on the rear cabinet

door. If these fences have already been installed, continue with the paper stacking inĆ

structions at step 4.

If not previously installed, install the front paper fence in the bracket as close as possible

to the paper stacking area as shown in Figure 2-12. The bracket is located in the upper

portion of the printer paper stacking area near the outer edges. The fence must be inĆ

stalled in the same bracket position on each side to maintain a straight vertical orientaĆ

tion.

Figure 2-12. Front Paper Fence Installation - Floor Cabinet Models

If not previously installed, install the rear paper fence on the inside of the rear cabinet

door placing the fence in the brackets at each upper edge of the door and in the bracket

centered on the lower edge of the door as shown in Figure 2-13.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды