Printronix P6000L Скачать руководство пользователя страница 205

Страница: 205 / 234

10-15

Installation

Shipping Restraint Removal

The printer shipping restraints must be removed prior to operation. The following tools are

required to remove the shipping restraints from a pedestal model:

3/32" inch hex wrench

3/8" nut driver

diagonal cutters

WARNING

Do not connect the ac power source before removing the shipping restraints. If the

power has been connected, disconnect it prior to performing the shipping restraint

removal procedures to prevent possible injury. In addition, the shipping restraints

must be installed whenever the printer or shuttle assembly is shipped or transĆ

ported to prevent damage.

The printer contains 2 platen restraint screws and a foam rubber pad inserted behind the tracĆ

tor sprockets. Each screw is tagged with a red WARNING label. After mounting the printer on

the pedestal or table top, perform the following procedure and refer to Figure 10-14 to reĆ

move the shipping restraints. A 3/8" nut driver and a 3/32" hex wrench are required.

Raise the printer cover.

Rotate the Vertical Position Knob (A) clockwise and pull the rubber pad down and out.

Cut and remove the tie wrap securing the Forms Thickness Adjustment Lever (B

)

on the

left side of the printer.

Notice the red WARNING label on the restraint screw (C) on the left side of the printer.

Using a 3/8" nut driver or wrench, remove the restraint screw from the left side.

Notice the red WARNING label on the right side restraint screw (D). Using a 3/32" hex

wrench, remove the restraint screw from the right side.

Cut and remove the nylon string binding the power cord at the rear of the printer.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды