Printronix P6000L Скачать руководство пользователя страница 4

Страница: 4 / 234

US and CANADA Radio Interference Note

Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. The

manufacturer is not responsible for any radio or television interference caused by using other than recommended

cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or

modifications could void the user’s authority to operate the equipment.

The input/output (I/O) cable must be shielded for the printer to comply with FCC rules and regulations Part 15

governing the radiation limits for Class “A” equipment.

This Class A digital apparatus meets all requirements of the Canadian Interference–Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du

Canada.

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user

may be required to take adequate measures.

Printronix, Inc. makes no representations or warranties of any kind regarding this material, including, but not limited to,

implied warranties of merchantability and fitness for a particular purpose. Printronix, Inc. shall not be held responsible

for errors contained herein or any omissions from this material or for any damages, whether direct, indirect, incidental

or consequential, in connection with the furnishing, distribution, performance or use of this material. The information in

this manual is subject to change without notice.

This document contains proprietary information protected by copyright. No part of this document may be reproduced,

copied, translated or incorporated in any other material in any form or by any means, whether manual, graphic,

electronic, mechanical or otherwise, without the prior written consent of Printronix, Inc.

Trademark Acknowledgements

The following trademarks are hereby acknowledged:

IBM is a registered trademark of International Business Machines.

QMS is a registered trademark of Quality Micro Systems, Inc.

Epson is a registered trademark of Epson America, Inc.

Printronix is a registered trademark of Printronix, Inc.

IGP is a trademark of Printronix, Inc.

RibbonMinder is a trademark of Printronix, Inc.



17500 Cartwright Road, P.O. Box 19559

Irvine, California 92713

Telephone (714) 863–1900 FAX (714) 660–8682

Technical Support (714) 221–2686



1988, 1989, 1996, PRINTRONIX, INC.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды