Printronix P6000L Скачать руководство пользователя страница 43

Страница: 43 / 234

2-23

Operation

Hex Code Printout

The hex code printout (called a hex dump) provides a listing of ASCII character data sent from

the host with their corresponding two-digit hex code. Nonprintable characters are indicated

with a period symbol. A p" before the hex code indicates an active Paper Instruction (PI) line;

a blank space before the hex code indicates an inactive PI line. To print the data stream sent

from the host computer in hex code with ASCII character equivalents, perform the following

steps.

Place the printer offline.

Repeatedly press CONFIG MENU until the DIAGNOSTICS message is displayed.

Press CONFIG VALUE; CONFIGURATION PRINTOUT will be displayed.

Press CONFIG MENU; PRINT DATASTREAM IN HEX CODE will be displayed.

Press RUN/STOP TEST; the display will be OFFLINE HEX DUMP.

Press ONLINE. The display will indicate ONLINE HEX DUMP.

Send the data from the host; the hex dump will print.

Press ONLINE again to stop the hex dump. Press RUN/STOP TEST to exit HEX DUMP.

Repeatedly press CLEAR FAULT to return to OFFLINE READY.

Place the printer online.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды