Printronix P6000L Скачать руководство пользователя страница 48

Страница: 48 / 234

Configuration

3-4

Press RUN/STOP TEST. All currently selected values are saved as the power-up default

value set.

Press CLEAR FAULT once to return to OFFLINE READ

Lock the printer configuration by simultaneously pressing the RUN/STOP TEST and

CONFIG MENU switches, and place the printer online.

The saved values remain effective until specifically changed by storing or saving other values. It

is important to remember that all currently selected values are saved, not just the specific value

most recently changed. Note also that values changed by control code sequences will also be

saved. For example, if the print mode is changed by control code and the configuration values

are subsequently saved, the print mode change is also saved. However, horizontal tab posiĆ

tions, margin settings, and character attributes such as bold, double high, etc. that can be

changed by control code but are not reflected on the display are not saved with the configuraĆ

tion value set.

Load Values

The current power-up default configuration value set can be loaded (restored) as needed. If,

for example, a number of configuration values were changed and stored for temporary use, the

complete power-up default set can be restored. This provides a convenient method of resetĆ

ting the printer's configuration to known values. The following general procedure can be used

to load (restore) the power-up default values.

Unlock the printer configuration by simultaneously pressing the RUN/STOP TEST and

CONFIG MENU switches.

Select and display LOAD PARAMETERS.

Repeatedly press CONFIG VALUE until the LOAD DEFAULT PARAMETERS mesĆ

sage is displayed.

Press RUN/STOP TEST. The current power-up default values are restored and in effect.

Press CLEAR FAULT once to return to OFFLINE READY.

Lock the printer configuration and place the printer online.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды