Printronix P6000L Скачать руководство пользователя страница 52

Страница: 52 / 234

Configuration

3-8

Hardware Jumper Configuration

Jumpers on the Logic C board are used to select a few configuration parameters. These jumpĆ

ers are installed for normal operation at the factory. However, certain applications may reĆ

quire a modification to the jumper configuration. To change any of these configuration

jumpers, the C3 logic board must be removed. Table 3-2 describes the jumper configurations.

To access the Logic C PCBA in floor cabinet model printers, the right side panel must be reĆ

moved and the card cage lowered. The following procedures provide instructions on accessing

the Logic C PCBA for both the floor cabinet and pedestal models.

WARNING

Any of these hardware changes require attention to detail on the PCBA assembly to

prevent damage. Some configurations require cutting an etch on the PCBA and solĆ

dering. These changes should only be performed by a trained technician.

Side Panel Removal - Floor Cabinet Model

To remove the right side panel, perform the following instructions and refer to Figure 3-2.

Turn the printer off and disconnect the ac power cord.

Raise the printer cover.

Disconnect the two ground wire connectors (A) from the corners of the side panel.

Loosen the side panel release screw (B) with the Phillips head screwdriver. Do not reĆ

move the screw; simply loosen it enough to slide in the notched cutout on the frame.

Using both hands, lift the side panel up and out from the bottom edge. The panel fits

snugly on four mounting studs (C). First time removal of the side panel may require extra

pressure to unseat the studs from the panel keyholes (D). The card cage can now be acĆ

cessed.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды