Printronix P6000L Скачать руководство пользователя страница 47

Страница: 47 / 234

3-3

Configuration

Set/Save/Load Configuration Values

Configuration values can be stored for temporary use or saved for more permanent use as the

power-up default configuration. In addition, current power-up default values can be loaded

(restored) for use as needed.

Set Values

Any configuration value can be changed as needed to meet application requirements. In order

to change a configuration parameter, the printer configuration must be unlocked. Select the

new value of the configuration parameter and press the RUN/STOP TEST switch. An asterisk

(*) will appear to the right of the value to indicate its selection.

NOTE: This type of change is only temporary. To permanently change a configuration

parameter, refer to the Save Values section of this chapter.

For example, to temporarily change the forms length parameter to 14.0 inches, unlock the

printer configuration and select and display a forms length value of 14.0 inches. Press the RUN/

STOP TEST switch to enter the value. 14.0 inches will now be used as the forms length parameĆ

ter.

Values stored in this way are replaced by the power-up default (saved) values when the printer

power is turned off and on. If a particular value is only required for a short term, limited appliĆ

cation, it can be stored temporarily. If the value is required for more permanent repeated use,

it should be saved as a power-up default.

Saved Values

Saved configuration values are the power-up default values. These are the parameters effecĆ

tive when the power is turned on. Until another value set is saved, the

Printronix

default conĆ

figuration values are effective at the initial power-up after receiving the printer from the

factory. The following general procedure can be used to save configuration values. Refer to the

Control Panel Switch Function Diagram for an illustration of the control panel switches reĆ

quired to select and display the parameter menus and values.

Unlock the printer configuration by simultaneously pressing the RUN/STOP TEST and

CONFIG MENU switches.

Select the value(s) required as the power-up defaults using the RUN/STOP TEST switch

to enter the change(s).

NOTE: Changing the Printer Compatibility under the Application Compatibility menu

affects other parameter value choices, automatically disabling some values and resetting

others. It also sets the current paper position as the top of form. Consequently, if the

Printer Compatibility configuration parameter is changed, it must be changed before

changing any other parameter values. Values changed prior to changing the Printer ComĆ

patibility value may be cancelled and not saved with the value set.

Select and display SAVE PARAMETERS.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды