Printronix P6000L Скачать руководство пользователя страница 45

Страница: 45 / 234

3-1

Configuration

CHAPTER 3

CONFIGURATION

Introduction

Configuration refers to a set of operating parameters that define how the printer will respond

to commands sent from the host computer. Most all the configuration parameters are selected

from the control panel as shown on the Control Panel Switch Function Diagrams. A few conĆ

figuration parameters are hardware selectable by jumpers on the Logic C board as described in

the Hardware Jumper Configuration section.

Before reconfiguring any printer function, be sure to read this entire chapter. The following

information is presented:

Lock/Unlock Printer Configuration

Configuration Menus

Configuration Procedure

Set/Save/Load Configuration Values

Default Configuration Values

Configuration Printout

Hardware Jumper Configuration

Control Panel Switch Function Diagram

Locking/Unlocking Printer Configuration

As previously described in the Operation chapter, the printer configuration is locked to preĆ

vent accidental or unintentional reconfiguration. Pressing the RUN/STOP TEST and CONĆ

FIG MENU switches simultaneously will alternately unlock or lock the printer configuration.

The Printer configuration must be unlocked to reconfigure the printer from the control panel.

NOTE: While DATA IN BUFFER is present, the printer configuration will remain

locked. Press PAPER ADVANCE, TOP-OF-FORM, or ONLINE to empty the printĆ

er's buffers and remove the DATA IN BUFFER condition.

Configuration Menus

The CONFIG MENU switch accesses and displays the various control panel selectable conĆ

figuration menus. The individual parameter values within each menu are displayed by repeatĆ

edly pressing the CONFIG VALUE switch. The following configuration menus appear on the

message display:

Ribbon Life

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды