Printronix P6000L Скачать руководство пользователя страница 192

Страница: 192 / 234

Installation

10-2

Site Requirements

When selecting the location for the printer, consider interface requirements, power requireĆ

ments, and environmental factors. Select a location with the proper power source available and

within the maximum cable length specifications to interface with the host computer. The

printer is designed to operate in a relatively dust free environment such as a computer room or

business office with an ambient temperature of 41

to 104

F (5

to 40

C) and a relative

humidity of 10% to 90%. The site selected for the printer must also allow air to circulate freely

all around the printer. A minimum of 3 feet clearance behind the printer should be provided to

allow air circulation and easy access to the paper stacking area. Figure 10-1 illustrates the site

requirements for floor cabinet model printers. Figure 10-2 illustrates the site requirements

for pedestal model printers.

CAUTION

The warranty may be voided if adequate ventilation is not provided. Overheating

and serious damage to the printer components can occur if the air vents at the sides

and bottom of the printer are blocked.

Figure 10-1. Site Requirements - Floor Cabinet Model

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды