Printronix P6000L Скачать руководство пользователя страница 162

Страница: 162 / 234

Interfaces

7-4

Paper Instruction (PI)

- Optional EVFU control signal from the host with the same timing as

the data lines. Sensing the PI line is controlled by printer configuration.

NOTE: The PI Line must be disabled (configuration option selected from the front

panel) if the host computer does not drive or control the PI Line. If the line is not conĆ

trolled by the host and sensing is enabled, rapid paper slewing will occur.

Table 7-2. Centronics Interface Connector Pin Assignments

INPUT SIGNALS

OUTPUT SIGNALS

SIGNAL

Data Line 1

Data Line 2

Data Line 3

Data Line 4

Data Line 5

Data Line 6

Data Line 7

Data Line 8

Paper Instr.

Data Strobe

Return

ACKNLG

SLCT/IONL

+5 Volts

Busy

Chassis

Not Used

Return

(Test Only)

Ground

27
15

28
32,13

16,17

30,31,

34,35, 36

Parallel Interface Configuration

The printer is configured at the factory for the type of interface used, either parallel or serial.

However, certain user selectable configuration options are available. The following configuraĆ

tion parameters can be verified or changed as necessary to meet specific application requireĆ

ments:

Input buffer size

Sense of Data Line 8

Sense of the Paper Instruction line

Data Polarity

Printer Error Polarity

Fast Busy

These parameters are displayed under the Application Compatibility and Interface CompatiĆ

bility menus selectable from the control panel. This data may be latched on either the leading

or the trailing edge of the Data Strobe signal by selecting the appropriate jumper on the Logic

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды