Printronix P6000L Скачать руководство пользователя страница 176

Страница: 176 / 234

Maintenance

8-6

Fault Messages

If a problem should arise, the printer displays certain fault messages. These messages indicate

the nature and location of user and service correctable errors. These message and their explaĆ

nations are listed in Table 8-1. After indicated fault has been corrected, press CLEAR

FAULT to return to ONLINE.

Table 8-1. Fault Messages

DISPLAY

OPERATOR

CORRECTABLE

EXPLANATION

CORRECTIVE

ACTION

FAULT CONDITION

PAPER OUT

PLATEN OPEN

PAPER JAM

RIBBON

POWER SUPPLY

SHUTTLE STALL

Yes

Paper Out

Platen Open

No Paper Motion

Ribbon Fault

DC Power Supply

Fault

Shuttle not

operating at

proper speed

Add paper

Contact an authorized

service representative.

contact an authorized

service representative.

Close the platen by

setting the Forms

Thickness Adjustment

Lever to the correct

position for the paper

used.

Check for and remove

any jammed paper in

the paper path.

Verify ribbon movement

during operation.

FAULT CONDITION
PROGRAM PROM

Upper/Lower

Contact an authorized

service representative.

program PROM error

FAULT CONDITION
FONT PROM

Upper/Lower

Contact an authorized

service representative.

font PROM error

FAULT CONDITION
RAM

Upper/Lower

Contact an authorized

service representative.

system RAM error

FAULT CONDITION

CHANGE RIBBON

Yes

RibbonMinder Message

Install a new ribbon

If this occurs frequently,

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды