Printronix P6000L Скачать руководство пользователя страница 24

Страница: 24 / 234

Operation

2-4

Locking/Unlocking Printer Configuration

To prevent accidental reconfiguration, the printer configuration (the parameter settings of the

printer) is normally locked. Before any new parameter settings are selected through the use of

the RUN/STOP TEST switch, the printer configuration must be unlocked. Simultaneously

pressing RUN/STOP TEST and CONFIG MENU, while the printer is OFFLINE READY,

alternately unlocks and locks the printer configuration. Resetting the printer or turning the

power off and on will also lock the printer configuration.

NOTE: While DATA IN BUFFER is present, the printer configuration will remain

locked. Press PAPER ADVANCE, TOP-OF-FORM, or ONLINE to empty the printĆ

er's buffers and remove the DATA IN BUFFER condition.

Control Panel

The printer control panel contains eleven switches, a power-on indicator, and a 32 character

alphanumeric Message Display as shown in Figure 2-3. Each switch is described on the followĆ

ing pages.

Power Indicator -

This indicator lights when the ac POWER switch is ON. On floor cabinet

models, the POWER switch is located on the lower left corner of the rear panel. On pedestal

models, the POWER switch is located on the bottom left side of the printer.

ON LINE -

Press this switch once to place the printer online or offline. The printer must be

online to print. When online, the display will indicate the current print mode and none of the

other control panel switches will function. When offline, the display will indicate OFFLINE

READY and the printer cannot communicate with the host computer. The printer will go ofĆ

fline automatically when a malfunction occurs and must be offline to change printing format or

configuration.

PAPER ADVANCE -

Momentarily press this switch to advance the paper one line or press and

hold the switch to advance the paper continuously. This switch functions only when the printer

is offline.

TOP OF FORM -

Press this switch once to advance one forms length (one page) to the top of

the next form. This switch functions only when the printer is offline.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды