Printronix P6000L Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 234

background image

2-19

Operation

7.

Verify the following and make any necessary adjustments.

a. The paper stack is centered on the tent

.

b. The paper perforation folds are folding in their natural prefolded direction.
c. The paper is following a straight path down to the tent in alignment with the outer

edges.

d. The paper is against the front paper fence as it rests centered on the tent.

8.

Run the printer and let approximately 15 to 20 sheets of paper stack.

9.

Again verify the items listed in step 7. Any adjustments to the paper stack can be made

while the printer is running. If an adjustment is made, again check the stack after approxiĆ

mately 15 to 20 sheets have been processed.

NOTE: If the paper is not stacking properly, check the following items in addition to

those listed in step 7.

1.

If printing occurs across the paper perforations, the paper will not stack corĆ

rectly. Adjust the Skip Over Perforation configuration parameter to eliminate

printing across the paper perforations.

2.

If the paper path is too close to either side panel, paper stacking can be disĆ

rupted. Adjust the paper path toward the center of the printer, away from the

side panels.

3.

The front paper fence may be incorrectly positioned. Reposition the front paĆ

per fence into one of the other bracket locations.

Selecting Print Mode

Characters and symbols are printed based on the print mode selected. During normal operaĆ

tion, the message display indicates the printer is online and the print mode currently selected.

For example,

ON LINE
DP AT 10 CPI

*

indicates the Data Processing print mode at 10 characters per inch is selected. To select a print

mode, perform the following instructions.

1.

Place the printer offline.

2.

Simultaneously press RUN/STOP TEST and CONFIG MENU to unlock the printer conĆ

figuration.

3.

Press PRINT MODE; the display will show the current print mode.

4.

Repeatedly press PRINT MODE until the required print mode is displayed.

5.

Press RUN/STOP TEST to select the displayed print mode.

6.

Press CLEAR FAULT to return to OFFLINE READY.

«
...
37
38
39
40
41
...
»

Содержание P6000L











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P6000L

I-Class Mark II

Бренд: Datamax Страницы: 12

Бренд: 3Doodler Страницы: 8

Бренд: Raymarine Страницы: 135

Бренд: Xante Страницы: 6

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Xerox Страницы: 5

WorkCentre 7328

Бренд: Xerox Страницы: 8

Бренд: Velleman Страницы: 44

Бренд: idp Страницы: 88

1900N - B/W Laser Printer

Бренд: Kyocera Mita Страницы: 286

ESP Office 6100 Series

Бренд: Kodak Страницы: 94

Бренд: BIXOLON Страницы: 20

Бренд: Creality 3D Страницы: 65

Бренд: Canon Страницы: 1384

Бренд: Canon Страницы: 642

da Vinci 1.0 Pro

Бренд: XYZ Printing Страницы: 22

Бренд: Epson Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды