Printronix P6000L Скачать руководство пользователя страница 165

Страница: 165 / 234

7-7

Interfaces

detected, a NAK (15 Hex) character is transmitted to the host upon receipt of the ETX characĆ

ter. The host is expected to repeat the data transmission.

NOTE: In ETX/ACK and ACK/NAK, avoid sending ETX (03 Hex) in Bit Image serial

matrix graphics data.

PARITY ERROR

- With an odd or even parity check in effect, the detected character error

shall be replaced with a question mark (?). If a parity error is detected, a NAK character is

transmitted to the host when the ACK/NAK protocol is selected. When parity is not checked,

parity errors are ignored and the characters are printed as received. Parity checking is a conĆ

figuration option selected from the control panel.

Serial Interface Configuration

The printer is configured at the factory for the type of interface used, either parallel or serial.

However, certain user selectable configuration options are available. The following configuraĆ

tion parameters can be verified or changed as necessary to meet specific application requireĆ

ments:

Input buffer size (selected from the Application Compatibility menu)

Data protocol (XON/XOFF, ACK/NAK, etc.)

Data rate (BAUD rate selected from the control panel; external clock jumper seĆ

lected)

Data word length and MSB function

Request to send behavior

Data terminal ready behavior

Reverse channel behavior

Protocol character assignment

These parameters are displayed under the Application Compatibility and Interface CompatiĆ

bility menus selectable from the control panel, except for external clock selection as noted

above. Refer to the Control Panel Switch Function diagram in the Configuration chapter for

detailed information on selecting the various parameter values.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды