Printronix P6000L Скачать руководство пользователя страница 44

Страница: 44 / 234

Operation

2-24

Printer Reset

The printer can be reset to the power-up configuration values whenever necessary. To reset

the printer, simply press CLEAR FAULT and RUN/STOP TEST simultaneously. The proceĆ

dure resets the printer to the configuration values last saved, not factory default values.

Running the Self-Test

P6000L/P6200L Series printers include various self-test functions. Use the self-test as

needed to determine if the printer is functioning normally.

To run the self-tests:

Place the printer offline.

Repeatedly press CONFIG MENU until DIAGNOSTICS is displayed.

Press CONFIG VALUE; CONFIGURATION PRINTOUT will be displayed.

Repeatedly press CONFIG MENU until either PRINTER TEST 8 INCH WIDTH or

PRINTER TEST FULL WIDTH is displayed.

Repeatedly press CONFIG VALUE until the appropriate test is displayed. Tests include

shift recycle, all Es, and others.

Press RUN/STOP TEST to begin the selected self-test; press RUN/STOP TEST again to

stop the test.

Examine the print quality. The characters should be solidly formed and aligned. If not, there

may be a problem with the printer.

Repeatedly press CLEAR FAULT to place the printer offline.

Place the printer online.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды